EQUIPMENT TRAY ASSEMBLY

TM 32-5410-215-14&P

(6) Remove file holder well (24) from work

(3) Position four rubber grommets (5) on work

surface (18) by removing seven screws (2), lock washers

surface assembly.

(1), and nuts (5).

(4) Position equipment tray weldment (4) over

two studs (6) and rest equipment tray weldment (4) on

c. Assembly.

work surface assembly.

(5) Install two springs (3) on two studs (6).

(6) Install two knobs (1) on two studs (6) and

(1) Install file holder well (24) on work surface

secure with two straight pins (2).

(18) using seven screws (2) lock washers (1), and nuts

(5).

(2) Install outer slides (7) on work surface (18)

5-23 LOWER CABINET ASSEMBLY. See figure E-1 1.

using eight flat washers (11), screws (10), and nuts (5).

(3) Install full extension slides (7) on drawer

a. Removal. Procedures detailed in paragraphs 5-

(16) using eight screws (2) and nuts (5).

18 a and b must be accomplished before proceeding

(4) Install lock tumbler (15) on drawer (16)

with paragraph b below.

using one flat washer (15), screw (15), pawl (15), and

locknut (15).

b. Disassembly.

(5) Install drawer (16) in work surface

(1) Remove sliding door assembly (11) from

assembly (18).

lower cabinet assembly (2) by removing 10 screws (13),

(6) Install

equipment

tray

assembly

flat washers (12), and nuts (3).

(paragraph 5-22b).

(2) Align screws (15) in top slide blocks (14)

d. Installation. Perform procedures detailed in

with holes in top of sliding door assembly (11).

paragraphs 5-18 c and d.

(3) Remove two slide blocks (14) from each

door top (10, 16) by removing eight screws (15), flat

5-22 EQUIPMENT TRAY ASSEMBLY. See figure E-13.

washers (8), and nuts (9).

(4) Remove doors (10, 16) from sliding door

a. Removal.

assembly (11).

(5) Remove two slide blocks (14) from each

(1) Remove two knobs (1) and two springs (3)

door bottom (10, 16) by removing eight screws (15), flat

from two studs (6) by removing two straight pins (2).

washers (8), and nuts (9).

(2) Lift equipment tray weldment (4) to clear

(6) Remove knob (22) from modified link lock

two studs (6) and remove equipment tray weldment from

(20) by removing spring pin (21).

work surface assembly.

(7) Remove bracket (19) from door (10) by

(3) Remove four rubber grommets (5) from

removing two screws (5), flat washers (6), and nuts (3).

work surface assembly.

(8) Remove modified link lock (20) and spring

(4) Remove two studs (6) from work surface

(23) from bracket (19) by removing spring pin (24).

assembly.

(9) Remove latch plate (7) from door (16) by

(5) Remove typewriter or other equipment

removing two screws (5) flat washers (6), and nuts (18).

from equipment tray weldment (4) by removing typewriter

(10) Remove shelf (4) from lower cabinet (2).

or other equipment retaining hardware set.

(11) Remove spring loaded plunger assembly

(1) from shelf (4) by grasping knob (1) and pin (1) with

b. Installation.

two pairs of pliers and pulling knob and pin apart with

flexing knob a few degrees.

NOTE

(12) Remove spring (1).

If the equipment tray weldment does

not have typewriter or other

NOTE

equipment mounting holes, drill them

The standoff in step (13) below is not

before doing step (1) in the procedure

reusable.

below. See paragraph 3-2e.

(13) Remove standoff (1) from shelf (4) by

(1) Install typewriter or other equipment on

drilling it out with a 7/16-in drill bit.

equipment tray weldment (4) using typewriter or other

c. Assembly

equipment retaining hardware set.

(2) Install two studs (6) on work surface

assembly.

5-14