Location of Repair Parts - TM-11-6625-922-150055

TM 11-6625-922-15

Code

Explanation

(2) The

quantitative

allowances

for

G -----Applies to major assemblies that are procured

organizational category of maintenance represents one

with PEMA funds for initial issue only to be

initial prescribed load for a 15-day period for the number

used as exchange assemblies at DSU and

of equipments supported.

Units and organizations

GSU category.

authorized additional prescribed loads will multiply the

number of prescribed loads authorized by the quantity of

(2) Maintenance code (M).

The lowest

repair parts reflected in the appropriate density column

category of maintenance authorized to install the listed

to obtain the total quantity of repair parts authorized.

item is noted here.

Code

Explanation

(3) Subsequent changes to organizational

Organizational Maintenance

allowances will be limited as follows: No change in the

General Support Maintenance

range of items is authorized. If additional items are

Depot Maintenance

considered necessary, recommendations should be

forwarded to Commanding General, U.S. Army

(3) Recoverability code (R). The information

Electronics Command, ATTN: AMSEL-ME-NMP-CW,

in this column indicates whether unserviceable items

Fort Monmouth, N. J. 07703, for exception or revision to

should be returned for recovery or salvage.

the allowance list. Revisions to the range of items

Recoverability code and its explanation is as follows:

authorized will be made by the USA ECOM National

Note.

When no code is indicated in the

Maintenance Point based upon engineering experience,

recoverability column, the part will be considered

demand data, or TAERS information.

expendable.

(4) The quantitative allowances for GS

Code

Explanation

category of maintenance will represent initial stockage

R -----Applies to repair parts and assemblies which are

for a 30-day period for the number of equipments

economically repairable at DSU and GSU

supported.

activities and normally are furnished by

supply on an exchange basis.

g. One-Year Allowances Per 100 Equipments/

b. Federal Stock Number Column. The Federal

Contingency Planning Purposes Column. Opposite the

stock number for the item is listed in this column.

first appearance of each item, the total quantity required

for distribution and contingency planning purposes is

c. Description Column. This column includes the

indicated. The range of items indicates total quantities

Federal-item name and any additional description of the

of all authorized items required to provide for adequate

item required, the manufacturer's part number

support of 100 equipments for one year.

(reference number), and the applicable five-digit Federal

Supply Code for Manufacturers. (para D-5). For

h. Depot Maintenance Allowance Per 100

subsequent appearances of the same item, the

Equipments Column. This column indicates the total

manufacturer's code and part number (reference

quantity of each item authorized depot maintenance for

number) are omitted. The words "same as" followed by

100 equipments. Subsequent appearances of the same

the index number assigned to the item when it first

item will have no entry in this column, but will have a

appeared in the list will follow the item name, e.g.,

reference in the description column to the first

"RESISTOR, FIXED, COMPOSITION: SAME AS A298".

appearance of the item.

Usable on code column is not used.

i. Illustrations Column.

d. Unit of Measure Column. The unit used as a

(1) Figure number (a). The number of the

basis of measure (e.g., ea, pr, ft, yd, etc.) is indicated in

illustration in which the item is shown is indicated in this

this column.

column.

e. Quantity Incorporated in Unit Column. The

(2) Item No. or reference designation (b).

quantity of repair parts in an assembly is given in this

The callout number or reference designation used to

column.

reference the item in the illustration appears in this

f. Maintenance Allowances Column.

column.

(1) The maintenance allowance columns are

divided into subcolumns. Indicated in each subcolumn

D-4. Location of Repair Parts

opposite the first appearance of the item is the total

a. This appendix contains three cross-reference

quantity of items authorized for the number of

indexes (sees V, VI, and VII), to be used to locate a

equipments supported. Subsequent appearances of the

repair part when either the Federal stock number,

same item will have no entry in the allowance columns,

reference number (manufacturer's part number), figure

but will have a reference in the description column to

number, or reference designation is known. The first

the first appearance of the item. Items authorized for

column in each cross-reference index is prepared,

use as required, but not for initial stockage, are

identified with an asterisk (*) in the allowance column.

D-2