 |
|||
|
|
|||
|
Page Title:
Table 3-5. TTY Loop Monitor Wiring List-Continued |
|
||
| ||||||||||
|
|
 TM 11-5895-1123-34
Table 3-5. TTY Loop Monitor Wiring List-Continued
FROM
TO
FROM
TO
FROM
TO
S2D-4
NC
S2E-2
S2E-3
S2E-17
S2F-7
S2D-6
NC
S2E-3
S2E-4 '
S2F-1
NC
S2D-7
NC
S2E-4
S2E-5
S2F-2
NC
S2D-8
S2F-8
S2E-5
S2E-7
S2F-3
NC
S2D-9
NC
S2E-6
NC
S2F-4
NC
S2D-10
NC
S2E-7
S2F-6
S2F-5
NC
S2D- 11
NC
S2E-9
NC
S2F-9
NC
S2D-12
NC
S2E-10
S2E-11
S2F-11
NC
S2D-13
NC
S2E-11
S2F-16
S2F-13
NC
S2D-15
S2E-8
S2E-1
S2E-12
S2F-13
NC
S2D-16
NC
S2E-12
S2E-13
S2F-14
NC
S2D- 17
S2F-17
S2E-13
S2E-14
S2F-15
NC
S2D-18
NC
S2E-14
S2E-15
S2F-18
NC
S2E-1
S2E-2
S2E-16
NC
NOTE
3-3.
Tools Required
In most cases, the cables involved in
these procedures have identifying
Item
NSN OR
markers to indicate where they are to be
No.
Qty
Nomenclature
FSCM NO.
connected. In example: THIS PART OF
3
Kit, tool (RCA-
THE MARKING IS NOT SIGNIFICANT
SM-A-777797)
FOR THIS EXPLANATION (XXXXXXX
4
Kit, Tool Electronic
J26). This marking indicates that the
Equipment
cable is to be connected to jack 26.
TK-105/G
When present, these markers may be
5
TPS tool, 12"
Trompeter RT-4L
used in lieu of tags where tagging is
6
TPS tool, 6"
Trompeter RT-4S
called for in disconnecting cables.
7
Screw starter
HJJ-3X-8
3-2.
Test Equipment Required
Item
NSN OR
No.
Qty
Nomenclature
FSCM NO.
1
AN/USM-223
2
Multimeter digital
6625-99-322-8715
(FLUKE-8000A)
Section II. MAINTENANCE OF COMMUNICATIONS
TTY/FSK PATCH PANEL SM-A-935888
the two line cords connected to rear of the unit.
NOTE
c. Disconnect the two line cords from the rear of
The Transmission Test Set SM-F-
the test oscillator and voltmeter.
935746 must be removed in order to
d. Continue to pull on the handles until the
remove the communications TTY/FSK
transmission test set is completely removed from the
patch panel.
rack.
3-4.
Removal of Transmission Test Set SM-F-
3-5.
Removal of Communications TTY/FSK Patch
935746
Panel SM-A-935888
a. Loosen the four captive screws on the front
a. Remove the transmission test set as outlined in
panel which holds the transmission test set to the rack.
paragraph 3-4 above.
b. Pull on the handles on the front panel to extend
b. Remove the four screws on the outside corners
the unit from the rack sufficiently to allow access to
3-32
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals