Special Information - TM-5-4940-225-20P0010

TM 5-4940-225-20P

Manufacturer (FSCM) in parentheses. The

NOTE

Cannibalization or salvage may be used as a

FSCM is used as an element in item identi-

source of supply for any items source coded

fication to designate manufacturer or dis-

above except those coded X1 and aircraft sup-

tributor or Government agency, etc., and

port items as restricted by AR 700-42.

is identified in SB 708-42. Items that are

(2) Maintenance code indicates the low-

included in kits and sets are listed below

est level of maintenance authorized to in-

the name of the kit or set with quantity of

stall the repair part and/or use the special

each item in the kit or set indicated in

tool or test equipment for each application.

front of the item name.

Capabilities of higher maintenance levels

d. Unit of Measure (U/M). Indicates the

are considered equal or better. Maintenance

standard or basic quantity by which the

codes are:

listed item is used in performing the actual

Code

Explanation

maintenance function. This measure is ex-

C . . . . . . Crew/Operator

pressed by a two-character alphabetical

O . . . . . . . Organizational maintenance

abbreviation, e.g., ea, in, pr, etc., and is

the basis used to indicate quantities and

(3) Recoverability code indicates

allowances in subsequent columns.

whether unserviceable items should be re-

e. Quantity Incorporated in Unit. Indi-

turned for recovery or salvage. Items not

cates the quantity of the item used in the

coded are nonrecoverable. Recoverability

breakout shown on -the illustration figure,

codes are:

which is prepared for and assembly group,

Explanation

Code

or an assembly. A "V" appearing in this

Repair parts (assemblies and components),

column in lieu of a quantity indicates that

special tools and test equipment which are

no specific quantity is applicable, e.g.,

considered economically reparable at direct

and general support maintenance levels. When

shims, spacers, etc.

the item is no longer economically reparable,

f. Fifteen-Day Organizational M a i n t e -

it is normally disposed of at the GS level.

nance Allowances. Items authorized for use

When supply considerations dictate, some of

as required but not for initial stockage are

these repair parts may be listed for automatic

return to supply for depot level repair as set

identified with an asterisk in the allowance

forth in AR 710-50. When so-listed, they will

column.

be replaced by supply on an exchange basis.

g. Illustration. This column is divided as

Repair Parts, Special Tools. and Test Equipment

"follows:

and assemblies which are economically repar-

(1) Figure number. Indicates the figure

able at DS and GS activities and which normal-

number of the illustration in which the item

ly are furnished by supply on an exchange

basis. When items are determined by a GS to

is shown.

be uneconomically reparable, they will be

(2) Item number. Indicates the callout

evacuated to a depot for evaluation and analysis

number used to reference the item on the

before final disposition.

illustration.

High dollar value recoverable repair parts,

special tools and test equipment which are

subject to special handling and are issued on

4. Special Information

an exchange basis. Such items will be repair-

a. Usable on codes are included in column

ed or overhauled at depot maintenance activ-

ities only. No repair may be accomplished at

(3). Uncoded items are applicable to all

lower levels,

models and/or serial number range. Identi-

Repair Parts, Special Tools and, Test Equipment

fications of the usable on codes used in this

specifically selected for salvage by reclama-

publication are:

tion units because of their precious metal

Code

content, critical materials, high dollar value

used on

or reusable casings or castings.

A . . . . . . . . . . .. Model SEORLT

b. Federal Stock Number. Indicates the

b. T h e b a s i s o f i s s u e f o r a u t h o r i z e d

Federal stock number assigned to the item

special tools, test and support equipment

is the number of end items of equipment

and will be used for requisitioning purposes.

c. Description. I n d i c a t e s t h e F e d e r a l

supported and the number of maintenance

personnel allocated to perform the required

item name and a minimum description re-

maintenance operations.

quired to identify the item. The last line

. c. Parts which require manufacture or

indicates the reference number followed

assembly at a level higher than that author-

by the applicable Federal Supply Code for