Location of Repair Parts - TM-11-6625-241-40P0004

*TM 11-6625-241-40P

b. Federal Stock Number. Indicates the Federal

1-4. Special Information

stock number assigned to the item and will be used for

a. Usable on codes are included in column 3. Un-

requisitioning purposes.

coded items are applicable to all models. Identification

c. Description. Indicates the Federal item name and

of the usable on codes used in this publication are -

a minimum description required to identify the item. The

last line indicates the reference number followed by the

Code

Used on

applicable Federal Supply Code for Manufacturer

BQ0

ZM-3/U

(FSCM) in parentheses. The FSCM is used as an

BQ1

ZM-3A/U

element in item identification to designate manufacturer

or distributor or Government agency, etc., and is

b. The basis of issue for authorized special tools,

identified in SB 708-42.

test and support equipment is the number of end items

d. Unit of Measure (U/M). Indicates the standard or

of equipment supported and the number of maintenance

basic quantity by which the listed item is used in

personnel allocated to perform the required mainte-

performing the actual maintenance function.

This

nance operations.

measure is expressed by a two-character alphabetical

abbreviation; e.g., ea, in, pr, etc., and is the basis used to

c. The following publications pertain to the ZM-3/U

indicate quantities and allowances in subsequent

and ZM-3A/U and its components:

columns. When the unit of measure differs from the unit

TM 11-5043-12

Operator's and Organizational

of issue, the lowest unit of issue that will satisfy the

Manual: Analyzers ZM-3/U

required units of measure will be requisitioned.

and ZM-3AfU.

e. Quantity Incorporated in Unit. This column

TM 11-5043-35

DS, GS, and Depot Mainte-

indicates the quantity of the item used in the equipment.

nance Manual: Analyzers

Subsequent appearances of the same item in the same

ZM-3/U and ZM-3A/U.

assembly are indicated by the letters "REF".

TM 11-6625241-20P

Organizational Maintenance

f. 30-Day DSIGS Maintenance Allowances.

Repair Parts and Special

NOTE

Tools Lists: Analyzers

ZM-3/U and ZM-3A/U.

Allowances in GS column are for GS mainte-

nance only.

1-5. Location of Repair Parts

(1) The repair parts indicated by asterisk entries

a. This manual contains one cross-reference index

in separate allowance columns for GS represent those

(sec IV) to be used to locate a repair part when either the

authorized for use at that category of maintenance to be

Federal

stock

number

reference

number

requisitioned on an "as required" basis, until stockage is

(manufacturer's part number) is known. The first column

based on demand in accordance with AR 710-2.

in the index is prepared in numerical or alphanumeric

(2) Allowance quantities are indicated in the

sequence in ascending order. The reference numbers

special tool lists section for special tools, TMDE, and

(manufacturer's part numbers) are listed immediately

other support equipment.

following the last listed Federal stock number in the

g. 1-Year Allowances Per 100 Equipments /Contin-

index of Federal stock numbers.

gency Planning Purposes. Column intentionally left

b. When the Federal stock number or reference

blank.

number is known, follow the procedures given in (1) and

h. Depot Maintenance Allowance Per 100 Equip-

(2) below.

ments.

This column indicates opposite the first

(1) Refer to the index of Federal stock numbers

appearance of each item the total quantity authorized for

(sec IV) and locate the Federal stock number or

depot maintenance of 100 equipments.

reference number. The FSN and reference number are

i. Illustration. This column is divided as follows:

cross-referenced to the applicable figure and item

(1) Figure number. Indicates the figure number

number or reference designation.

of the illustration on which the item is shown in TM 11-

(2) Refer to the repair parts list (sec II) and

5043-35.

locate the figure number (col 10a) and item number or

(2) Items number. Indicates the item number or

reference designation (col 10b) as noted in the FSN

reference designation used to reference the item in the

index.

illustration.