UPPER CABINET ASSEMBLY

TM 32-5410-215-14&P

(1) Unplug work console electrical cord (11)

(2) Install work surface assembly (39) to lower

from wall receptacle.

cabinet assembly (38) using eight screws (11), flat

(2) Detach work console (11) from bracket

washers (13), and nuts (7).

(22) by removing two screws (26), lock washers (24),

(3) Install drawer in work surface assembly

and flat washers (23).

(39).

(3) Remove work console front base plate

(4) Install tack-board assembly (41) to work

(33, figure E-7) by removing two screws (31, figure E-7),

surface assembly (39) using six screws (40).

lock washers (12, figure E-7), and flat washers (32,

(5) Install upper cabinet assembly (5) to tack-

figure E-7).

board assembly (41) using six screws (8) and nuts (7).

(4) Detach work console from shelter floor by

(6) Install electrical duct extension (27).

removing four screws (26), lock washers (24), and flat

(7) Secure to work surface assembly (39)

washers (23). Remove work console.

using four flat washers (13), lock washers (12), and

screws (11).

b. Disassembly. See figure E-7.

(8) Secure electrical duct extension (29) to

upper cabinet assembly (5) and tack-board assembly

(41) using six screws (8) and nuts (7).

(1) Remove bracket (3) and stiffener (4) from

(9) Feed wires from electrical duct extension

upper cabinet assembly (5) by removing four nuts (6),

(27) through hole in top of duct into upper cabinet

screws (1), and lock washers (2).

assembly (5).

(2) Tag and disconnect leads to light unit

(10) Install and tighten connector (9).

assembly (42).

(11) Install cover (14) on electrical duct

(3) Remove light unit assembly (42) from

extension (29) using six flat washers (13), lock washers

upper cabinet assembly (5) by removing six screws (43),

(12), and screws (11).

lock washers (13), and nuts (7).

(12) Install light unit assembly (42) to upper

(4) Remove cover (14) from electrical duct

cabinet assembly (5) using six lock washers (13), screws

extension (27) by removing six screws (11), lock

(43), and nuts (7).

washers (12), and flat washers (13).

(13) Connect leads to light unit assembly (42).

(5) Detach electrical duct extension (27) from

(14) Install bracket (3) and stiffener (4) on

upper cabinet assembly (5) and tack-board assembly

upper cabinet assembly (5) using four lock washers (2),

(41) by removing six screws (8), six nuts (7), and one

screws (1), and nuts (6).

connector (9).

d. Installation. Item numbers below refer to figure

(6) Detach electrical duct extension (27) from

E-1, sheet 2 of 2, unless otherwise indicated.

work surface assembly (39) by removing four screws

(1) Position work console over shelter floor

(11), lock washers (12), and flat washers (13). Remove

mounting holes.

electrical duct extension.

(2) Secure work console to shelter floor using

(7) Remove upper cabinet assembly (5) from

four flat washers (23), lock washers (24), and screws

tackboard assembly (41) by removing six screws (8) and

(26).

nuts (7).

(3) Install work console front base plate (33,

(8) Remove tack-board assembly (41) from

figure E-7) using two flat washers (32, figure E-7), lock

work surface assembly (39) by removing six screws (40).

washers (12, figure E-7), and screws (31, figure E-7).

(9) Remove drawer from work surface

(4) Secure work console to bracket (22) using

assembly (39).

two flat washers (23), lock washers (24), and screws

(10) Remove work surface assembly (39) from

(26).

lower cabinet assembly (38) by removing eight screws

(5) Plug work console electrical cord into wall

(11), flat washers (13), and nuts (7).

receptacle.

(11) Remove cabinet base (35) from lower

cabinet assembly (38) by removing four screws (1), lock

washers (34), and flat washers (2).

5-19 UPPER CABINET ASSEMBLY. See figure E-8.

c. Assembly. See figure 3-7.

a. Removal. Procedures detailed in paragraphs 5-

(1) Install cabinet base (35) to lower cabinet

18 a and b must be accomplished before proceeding

assembly (38) using four screws (1), lock washers (34),

with paragraph b below.

and flat washers (2).

b. Disassembly.

(1) Open cabinet door (7).

(2) Remove cabinet door (7) from upper

cabinet assembly (1) by removing seven screws (8) and

nuts (9)

5-12