|
|
TM 11-6625-937-12
b. Running Spares. No running spares are provided with the equipment.
c. Battery, Dry BA-399/U. The battery is required, but not furnished as part of the equipment. Refer to paragraph 1-
9.
1-7. Description of Indicator, Channel Alignment ID-1189/PR
The ID-1189/PR is inclosed in a ruggedized type constructed case. The case when closed is watertight and airtight and
contains a breather valve which can be manually operated to equalize pressure between the inside and outside of the
case. A screwdriver, an alignment tool, an antenna, and instruction plates are secured to the inside cover of the case.
Two additional adapters are included inside the cover of ID-1189(XE-2)/PR case only. The ID-1189/PR circuits are
contained within the body of the case and attached to and covered by a plate assembly. The top of the plate assembly is
a control panel which contains the operating controls, jacks, and a meter. Units, such as battery type BA-399/U or BA-
505/U, Receiving Set, Radio AN/PRR-9, or Transmitting Set, Radio AN/PRT4, when being tested or aligned, are plugged
directly into the appropriate jack on the control panel. For the ID-1189 (XE-2)/PR only, the adapters are used between
the appropriate control panel jack and the AN/PRR-9(XE-9) or BA-4534/U. The control panel meter indicates the results
of tests or alignment. The meter face is worked on one scale to indicate relative center readings for alignment, and also
contains a GOOD and BAD scale to indicate a battery condition. On the ID-1189(XE-2)/PR only, the meter glass
contains an additional indicating scale that is used when testing the BA-4534/U.
1-8. Description of Minor Components
a. The screwdriver has a wooden handle, and a 3/8-inch wide hardened steel blade. It is used for disassembling the
AN/PRR-9, AN/PRR-(XE-9), and AN/PRT-4 for alignment purposes.
b. The alignment tool is an insulated alignment tool with a hardened steel blade. The 1/4-inch blade tip fits all the
capacitors, coils, and resistors adjusted during alignment of a receiver or transmitter.
c. The antenna is a 17-inch long whip antenna with a phone tip at one end and a ball at the other. It is used during
portions of the alignment procedures of a receiver or transmitter.
d. Instruction plates, laminated cards in plastic, are contained within the cover of Case, Indicator CY-6078/PR. Two
plates are provided; one contains detailed battery test and alignment information for the AN/PRT-4 and the other
contains alignment information for the AN/PRR-9. A third plate, supplied with the ID-1189(XE-2)/PR only, contains
alignment information for the AN/PRR-9(XE-9) and battery test information for the BA-4534/U. The plates are held to the
case lid by a nylon cord.
e. Adapter, Connector U-389(XE-1)/PR (battery adapter) contains a connector at the bottom end designed to fit the
RCVR BAT. connector on the top plate assembly of the ID-1189(XE-2)/PR. The top of the adapter contains a two-
conductor plug which fits the connector of Battery, Dry, BA-4534/U. When not in use, the adapter is stored in the lid of
the ID-1 189 (XE-2) /PR.
f. Adapter, Receiving Set MX-8512(XE-1)/PR (RECEIVER ALIGNMENT adapter) is used for aligning Receiving Set,
Radio AN/ PRR-9(XE-9). In use, it is installed over the RECEIVER ALIGNMENT receptacle of the ID-1189(XE-2)/PR.
The adapter contains necessary electrical connectors and receptacles for connection to the ID-1189 (XE-2) /PR circuitry.
When not in use, the adapter is stored in the case lid.
1-9. Additional Equipment Required
Battery, Dry BA-399/U is used as power for operation of the ID-1189/PR but-not furnished as part of the equipment. This
is the same battery type used in the AN/PRT4. It contains two 7-1/2-volt sections connected in series.
Change 3 1-3
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |