Quantcast CHAPTER 4 LELAND AIRBORNE MODEL

 

Click here to make tpub.com your Home Page

Page Title: CHAPTER 4 LELAND AIRBORNE MODEL
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 3-15. Schematic diagram model 5027RD.
Up
TB-9-2920-225-34-1 100 AMP Regulator (Solid State) Manual
Next
Figure 4-2. Transistor resistance checks (Leland Airborne model).
TB 9-2920-225-34-1
CHAPTER 4
LELAND AIRBORNE MODEL
4-1. Introduction. One model was produced by
washers and rubber insulators. Visually inspect
Leland Airborn Products Division of American
the circuit board for burnt components. Replace
Machine and Foundry Co. The manufacturer's
the circuit board through cannibalization if burnt
name is now:
components are found. Carefully reinstall the
transistor mounting plate.
CODE IDENT 07639 (FSCM)
Leland Electrosystems Inc.
c. Regulator Verification Check. After perform-
740 E. National Road
ing the regulator appears to be in good condition,
P.O. BOX 128
check its performance on a test stand.
Vandalia, OH 45377
If the regulator fails this check, proceed to para-
TELEPHONE AC 513898-5881
The manufacturer is also now known as AMF
4-3. Bench Testing.
Electrosystems Division at the same address. The
manufacturer's part number for this model is CSV
a. General. Figures 4-1 and 4-2 show the
2183-1.
method for testing NPN transistors. Figure 4-3
shows a plan view of the circuit board assembly,
4-2. General Inspection.
the regulator with the cover and circuit board re-
moved, and an electrical schematic diagram of the
a. Regulator Box Assembly (external). Check
regulator.
for missing or stripped cover, connector and
mount retainer screws and voltage adjustment ac-
b. Diode and Relay.
cess plug. Check connectors for signs of arcing,
(1) Remove six screws and place the circuit
bent or pushed in pins, broken connectors and
board to one side.
thread damage. Correct deficiencies by utilization
(2) Place positive probe of ohmmeter to pin
of serviceable components from unrepairables or
F of connector J2, (see fig. 4-3).
requisitioning components from the manufacturer.
( 3 ) Place negative probe to TP1. Meter
The pin receptacle (J2) is part number 19207
should indicate low resistance.
7064429 or MS3102A2822P per MIL-C-5015.
(4) Reverse probes. Meter should indicate
The socket receptacle (Jl) is part number 19207-
7064706, for which there is no equivalent NSN
(5) If other readings are obtained, replace
number.
diode CR6, (see fig. 4-3).
As assembly is available from Bendix.
(6) Move negative probe to TP2. Meter
should read approximately 250 ohms.
CODE IDENT 77820 (FSCM)
Bendix Corp. The Electrical
(7) If another reading is obtained, replace
Components Div.
the relay, (see fig. 43).
Sherman Avenue
c. Field Discharge Diode.
Sidney, NY 13838
(1) Place positive probe of ohmmeter to pin
It should be ordered as part number 6042228
E of connector J1 (see fig. 4-3).
10S, it is possible that extensive damage has been
(2) Place negative probe to pin B of J1.
done and the regulator cannot be easily repaired.
Meter should indicate low resistance.
Components should be performance tested and re-
(3) Reverse the probes. Meter should indi-
tained if acceptable. Check for disconnected or
cate high resistance.
burnt wires, missing components and replace/re-
(4) If other readings are obtained, replace
pair as necessary. Carefully remove the transistor
diode CR7.
mounting plate noting the position of the screws,
4-1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.