Click here to make tpub.com your Home Page

Page Title: COOLING SYSTEMS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

COOLING SYSTEMS
ENGINE JACKET WATER
instructions included with the cleaner.
CHECKING COOLANT LEVEL
Check coolant level with the engine cool and stopped:
The cooling system can be cleaned using oxalic acid
1.  Slowly loosen the filler cap and release
and sodium carbonate as follows:
pressure.
1.  Fill  the  cooling  system  with  a  solution
consisting of one pound of oxalic acid or
WARNING
sodium bisulphate (NaHSO4) with every 5
Be careful if engine is warm; steam may
gallons of water (mix 0.4 kg.  with every 10
spray. Avoid being burned.
liters of water).
2.  Push downward and turn the cap until it is
2.  Start the engine and operate at operating
released.
temperatures for 1/2 to 1 hour.
3.  Maintain coolant level to within 1/2 inch (1 cm)
3.  Stop the engine and drain the cooling system.
below bottom of fill pipe.  The coolant will
4.  Flush the system with clean water until the
expand as it is heated.
draining water is clear.
4.  Make-up coolant must be one of the following:
5.  Install all drain plugs.
a.  Permanent anti-freeze and water solution.
6.  Fill with a solution consisting of 1/2 pound of
b.  Drinkable water and rust inhibitor solution.
For emergencies, and only as a "temporary
sodium carbonate crystals (Na2CO3, 10H20)
fix" until the cooling system can be
with every 10 gallons of water (mix 0.06 kg
returned to either (a) or (b), use either:
with every 10 liters of water).
c.  Drinkable water.
7.  Start and run the engine for 10 minutes.
d.  Any available water.
8.  Stop the engine and drain the cooling system.
"Drinkable water" is clean water that is low in scale
9.  Flush the cooling system with clean water.
forming minerals - not softened water.  Never add
10. Install all drain plugs.
coolant to an overheated engine; allow it to cool first.
FILLING COOLING SYSTEM
Check  specific  gravity  of  anti-freeze  solution
1.  Add anti-freeze, if required.
frequently  in  cold  weather  to  assure  adequate
2.  Fill to correct level with coolant which is free as
protection.
possible from scale forming minerals. Do not
use softened water.
CAUTION
3.  Start and run engine for 10 minutes.
Add coolant slowly to a hot engine to
4.  Remove the radiator cap and check the coolant
level.
prevent possible cracking or distorting the
5.  Add coolant, if needed, until coolant level is
cylinder head.
within 1/2 inch (1 cm) below bottom of the filler
tube.
DRAINING RADIATOR
6.  Install the radiator cap.
Whenever it is necessary to drain the cooling system
Most commercial antifreeze solutions contain rust
for repairs:
inhibitors, however, it is recommended the adding of
1.  Remove the filler cap.
Caterpillar Coolant System Conditioner to glycol base
2.  Open the drain valve for the radiator.
antifreeze if protection is for temperatures above -20
F
(-29 ). If protection is for temperatures -20 (-20 )
C
F
C
DRAINING COMPLETE COOLING SYSTEM
or below, do not add conditioner.  Follow instructions
given on the container.
1.
Drain the radiator; see the topics above.
2.
Remove front cover drain plug.
3.
Remove both engine block drain plugs.
4.
Remove the oil cooler coolant drain plug.
WARNING
5.
Remove the coolant; then install all drain
Inhibitor contains alkali.  Avoid contact
plugs.
with eyes.  Avoid prolonged or repeated
FLUSHING COOLING SYSTEM
contact with skin.
To clean the cooling system, any good commercial
radiator cleaning solution can be used.  Follow the
17

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business