Special Information - TM-11-6625-241-20P0004

d. Unit of Measure (UIM). Indicates the standard

Manual: Analyzers ZM-3/U and ZM-

3A/U.

or basic quantity by which the listed item is used in

TM 11-5043-35

DS, GS, and Depot Maintenance

performing the actual maintenance function.

This

Manual: Analyzers ZM-3U and ZM-

measure is expressed by a two-character alphabetical

3A/U.

abbreviation; e.g., ea, in, pr, etc., and is the basis used to

indicate quantities and allowances in subsequent

columns. When the unit of measure differs from the unit

1-5. Location of Repair Parts

of issue, the lowest unit of issue that will satisfy the

required units of measure will be requisitioned.

a. This manual contains one cross-reference

index (sec V) to be used to locate a repair part when

e. Quantity Incorporated in Unit. This column

either the Federal stock number or reference number

indicates the quantity of the item used in the equipment.

(manufacturer's part number) is known. The first column

Subsequent appearances of the same item in the same

in the index is prepared in numerical or alphanumeric

assembly are indicated by the letters "REF".

sequence in ascending order. The reference numbers

f. 15-Day

Organizational

Maintenance

(manufacturer's part numbers) are listed immediately

Allowance.

following the last listed Federal stock number in the

index of Federal stock numbers.

(1) The repair parts indicated by an asterisk

in the allowance column represent those authorized for

b. When the Federal stock number or reference

use at the organizational category, and will be

number is known, follow the procedures given in (1) and

requisitioned on an "as required" basis, until stockage is

(2) below.

based on demand in accordance with AR 710-2.

(2) Major Army commanders are authorized

(1) Refer to the index of Federal stock

to approve reduction in the range of support items

numbers (sec V) and locate the Federal stock number or

authorized for use in units within their commands.

reference number. The FSN and reference number are

Recommendations for increase in range of items

cross-referenced to the applicable figure and item

authorized for use will be forwarded to Commander, US

number or reference designation.

Army Electronics Command, ATTN: AMSELMA-CW,

(2) Refer to the repair parts list (sec III) and

Fort Monmouth, NJ., 07703. Any changes approved will

locate the figure number (col 7a) and item number or

be reflected in a revision to the RPSTL.

reference designation (col 7b) as noted in the FSN index.

(3) Allowance quantities are indicated in the

c. When the figure and item number or reference

special tools list section for special tools, TMDE, and

other equipment.

designation are known, scrutinize columns 7a and 7b of

g. Illustration. This column is divided as follows:

the repair parts list (sec III) until the item is located.

(1) Figure number. Indicates the figure

d. When the FSN, reference number, figure

number of the illustration on which the item is shown in

TM 11-5043-35.

number, item number and reference designation are not

(2) Item number. Indicates the item number

known, scrutinize column 3 of the repair parts list (sec

or reference designation used to reference the item in

III), which is arranged in alphabetical order.

the illustration.

1-6. Abbreviations

1-4. Special Information

Not applicable.

a. Usable on codes are included in column 3.

Uncoded items are applicable to all models.

1-7. Reporting

Equipment

Publication

Identification of the usable on codes used in this

Improvements.

publication are --

The

reporting

errors,

omissions,

and

Code

Used on

recommendations for improving this publication by the

BQ∅

ZM-3/U

individual user is encouraged.

Reports should be

submitted on DA Form 2028 (Recommended Changes

BQ1

ZM-3A/U

f. The following publications pertain to the ZM-

to Publications) and forwarded direct to Commander, US

Army Electronics Command, ATTN: AMSEL-MA-CW,

3/U and ZM-3AJU and its components:

Fort Monmouth, N.J., 07703.

TM 11-5043-12

Operator's and Organizational