Special Inforrnation

b. Federal Stock Number. Indicates the Federal

of maintenance to, be requisitioned on an "as

stock number assigned to the item.

required" basis, until stockage is based on demand in

accordance with AR 710-2.

NOTE

For requisitioning purposes, the Federal

(2) Allowance quantities are indicated in the

special tool lists section for special tools, TMDE, and

stock number must be converted to the

other support equipment.

National stock number by adding "-00-"

after the Federal stock classification (FSC)

h. 1-year Allowances Per 100 Equipmental

code (first four digits). For example, FSN

Contingency Planning Purposes.. Column inten-

6625-553-0142 converts to NSN 6625-00-

tionally left blank.

553-0142.

i. Depot Maintenance Allowance Per 100 Equip-

c. Description. Indicates the Federal item name

ments. This column indicates opposite the first

and a minimum description required to identify the

appearance of each item the total quantity au-

item. The last line indicates the reference number

thorized for depot maintenance of 100 equipments.

followed by the applicable Federal Supply Code for

j. Illustration. Not applicable.

Manufacturer (FSCM) in parentheses. The FSCM is

used as an element in item identification to designate

1-4. Special Inforrnation

Manufacturer or distributor or Government agency,

Usable on codes are included in column 3. Uncoded

etc., and is identified in SB 708-42.

items are applicable to all models. Identification of

d. Unit of Measure (U/M). Indicates the standard

the usable on codes used in this publication are:

or basic quantity by which the listed item is used in

Code

Used on

performing the actual maintenance function. This

B6J

H140A/U

measure is expressed by a two character alphabeti-

cal abbreviation; e.g., ea, in, pr, etc., and is the basis

1-5. Location of Repair Parts

used to indicate quantities and allowances in

subsequent columns. When the unit of measure

a. This manual contains one cross-reference index

differs from the unit of issue, the lowest unit of issue

(see VII) to be used to locate a repair part when either

that will satisfy the required units of measure will be

the Federal stock number or reference number

requisitioned.

(manufacturer's part number) is known. The first

e. Quantity Incorporated in Unit. This column

column in the index is prepared in numerical or

indicates the quantity of the item used in the

alphanumeric sequence in ascending order. The

equipment.

reference numbers (manufacturer's part numbers)

f. 15-Day Organizational Maintenance Allowances.

are listed immediately following the last listed

(1) The repair parts indicated by an asterisk in

Federal stock number in the index of Federal stock

the allowance column represent those authorized for

numbers.

use at the organizational category, and will be

b. When the Federal stock number or reference

requisitioned on an "as required" basis, until

number is known, follow the procedures given in (1)

stockage is based on demand in accordance with AR

and (2) below.

710-2.

(1) Refer to the index of Federal stock numbers

(2) Major Army commanders are authorized to

(see VII), and locate the Federal stock number or

approve reduction in the range of support items

reference number. The FSN and reference number

authorized for use in units within their commands.

are cross-referenced to the applicable figure and

Recommendations for increase in range of items

item number or reference designation.

authorized for use will be forwarded to Commander,

(2) Refer to the repair parts list (see III and V)

US Army Electronics Command, ATTN: AMSEL

and locate the figure number (col 7a -- 20P,

MA-CW, Fort Monmouth, NJ 07703.

10a -- 34P) and item number or reference designa-

(3) Allowance quantities are indicated in the

tion (col 7b -- 20P, 10b -- 34P) as noted in the FSN

special tools list section for special tools, TMDE, and

index.

other support equipment.

c. When the figure and item number or reference

g. 30-Day DS/GS Maintenance Allowance.

designation are known, scrutinize columns 7a and

NOTE

7b -- 20P and 10a and 10b -- 34P, of the repair parts

Allowances in GS column are for GS

list (see 111 and V) until the item is located.

maintenance only.

d. When the FSN, reference number, figure

number, and item number are not known, scrutinize

(1) The repair parts indicated-by asterisk entries

in separate allowance columns for DS and GS

column 3 of the repair parts list (see III and V), which

is arranged in alphabetical order.

represent those authorized for use at that category