SECTION I INTRODUCTION - TM-11-5805-714-34P0003

SECTION I

INTRODUCTION

PE - Support equipment procured for initial issue or

1. Scope

outfitting to specified maintenance repair activities.

This manual lists spares and repair parts; Special Tools;

PF - Support equipment which will not be stocked but

special test, measurement, and diagnostic equipment

which will be centrally procured on. demand.

(TMDE), and other special support equipment required

PG - Item procured and stocked to provide for sustained

for performance of direct support and general support

support for the life of the equipment. It is applied to

maintenance of the C-10333/TTC-39(V). It authorizes

an item peculiar to the equipment which, because of

the requisitioning and issue of spares and repair parts as

probable discontinuance or shutdown of production

indicated by the source and maintenance codes.

facilities, would prove uneconomical to reproduce at a

2. General

later time.

This Repair Parts and Special Tools List is divided into

KD - An item of a depot overhaul/repair kit and not

the following sections:

purchased separately. Depot kit defined as a kit that

a. Section II. Repair Parts List. A list of spares

provides items required at the time of overhaul or

and repair parts authorized for use in the performance of

repair.

maintenance. The list also includes parts which must be

KF - An item of a maintenance kit and not purchased

removed for replacement of the authorized parts. Parts

separately. Maintenance kit defined as a kit that

lists are composed of functional groups in numeric

provides an item that can be replaced at

sequence, with the parts in each group listed in figure

organizational or intermediate levels of maintenance.

and item number sequence.

KB - Item included in both a depot overhaul/repair kit

b. Section III. Special Tools List. Not applicable.

and a maintenance kit.

c. Section IV. National Stock Number and Part

MO - Item to be manufactured or fabricated at

Number Index. A list, in National item identification

organizational level.

number (NIIN) sequence, of all National stock numbers

MF - Item to be manufactured or fabricated at the direct

(NSN) appearing in the listings, followed by a list, in

support maintenance level.

alphanumeric sequence, of all part numbers appearing

MH - Item to be manufactured or fabricated at the

in the listings.

National stock numbers and part

general support maintenance level.

numbers are cross-referenced to each illustration figure

MD - Item to be manufactured or fabricated at the depot

and item number appearance.

maintenance level.

3. Explanation of Columns

AO - Item to be assembled at organizational level.

a. Illustration. This column is divided as follows:

AF - Item to be assembled at direct support

(1) Figure Number.

Indicates the figure

maintenance level.

number of the illustration on which the item is shown.

AH - Item to be assembled at general support

(2) Item Number.

The number used to

maintenance level.

identify item called out in the illustration.

AD - Item to be assembled at depot maintenance level.

XA - Item is not procured or stocked because the

b. Source, Maintenance, and Recoverability (SMR)

requirements for the item will result in the replacement

Codes.

of the next higher assembly.

(1) Source code. Source codes indicate the

XB - Item is not procured or stocked. If not available

manner of acquiring support items for maintenance,

through salvage, requisition.

repair, or overhaul of end items. Source codes are

XC - Installation drawing, diagram, instruction sheet,

entered in the first and second positions of the Uniform

field service drawing, that is identified by

SMR Code format as follows:

manufacturer's part number.

Code

Definition

XD - A support item that is not stocked. When required,

PA - Item procured and stocked for anticipated or known

item will be procured through normal supply channels.

usage.

NOTE

PB - Item procured and stocked for insurance purpose

Cannibalization or salvage may be

because essentiality dictates that a minimum quantity

used as a source of supply for any

be available in the supply system.

items source coded above except

PC - Item procured and stocked and which otherwise

those coded XA and aircraft support

would be coded PA except that it is deteriorative in

items as restricted by AR 750-1.

nature.

(2) Maintenance code. Maintenance codes

PD - Support item, excluding support equipment,

are assigned to indicate the levels of maintenance

procured for initial issue or outfitting and stocked only

authorized to USE and REPAIR support items. The

for subsequent or additional initial issues or outfittings.

maintenance codes are entered in the third and fourth

Not subject to automatic replenishment.

positions of the Uniform SMR Code format as follows: