Location of Repair Parts - TM-11-5905-200-24P0004

Unit of Measure (U/M).

Code

Used on

Indicates the

standard or basic quantity by which the listed item is

AD5

TS402/U

used in performing the actual maintenance function.

AD6

TS402A/U

The following publication pertains to the

This measure is expressed by a two-character

alphabetical abbreviation; e.g., ea, in, pr, etc., and is the

equipment and its components:

basis used to indicate quantities and allowances in

TM 11-2044

Attenuator TS-402/U and

subsequent columns. When the unit of measure differs

TS402A/U.

from the unit of issue, the lowest unit of issue that will

satisfy the required units of measure will be

1-5. Location of Repair Parts

requisitioned.

This manual contains one cross-reference

Quantity Incorporated in Unit. This column

index (sec VII) to be used to locate a repair part when

indicates the quantity of the item used in the equipment.

either the Federal stock number or reference number

Subsequent appearances of the same item in the same

(manufacturer's part number) is known. The first column

assembly are indicated by the letters "REF".

in the index is prepared in numerical or alphanumeric

15-Day

Organizational

Maintenance

sequence in ascending order. The reference numbers

Allowances. Not applicable.

(manufacturer's part numbers) are listed immediately

30-Day DS/GS Maintenance Allowances.

following the last listed Federal stock number in the

index of Federal stock numbers.

When the Federal stock number or

NOTE

reference number is known, follow the procedures given

Allowances in GS column

are

for

in (1) and (2) below.

maintenance only.

(1) Refer to the index of Federal stock

numbers (sec VII). and locate the Federal stock number

(1) The repair parts indicated by asterisk

or reference number. The FSN and reference number

entries in separate allowance columns for DS and GS

are cross-referenced to the applicable figure and item

represent those authorized for use at that category of

number or reference designation.

maintenance to be requisitioned on an "as required"

(2) Refer to the repair parts list (sec III

basis, until stockage is based on demand in accordance

and V) and locate the figure number (col 7a-20P, 10a-

with AR 710-2.

34P) and item number or reference designation (col 7b-

(2) Allowance quantities are indicated in

20P, 10b-34P) as noted in the FSN index.

the special tool lists section for special tools, TMDE, and

When the figure and item number or

other support equipment.

reference designation are known, scrutinize columns 7a

1-Year

Allowances

Per

100

and 7b-20P and 10a and l0b-34P, of the repair parts list

Equipment./Contingency Planning Purposes. Column

(sec III and V) until the item is located.

intentionally left blank.

When the FSN, reference number, figure

Depot Maintenance Allowance Per 100

number. and item number are not known, scrutinize

Equipments. This column indicates opposite the first

column 3 of the repair parts list (see III and V), which is

appearance of each item the total quantity authorized for

arranged in alphabetical order.

depot maintenance of 100 equipments.

Illustration.

1-6. Abbreviations

(1) Figure number. Indicates the figure

Not applicable.

number of the illustration on which the item is shown in

TM 11-2044.

1-7. Reporting

Equipment

Publication

(2) Item number.

Indicates the item

Improvements

number or reference designation used to reference the

The

reporting

errors,

omissions,

and

item in the illustration.

recommendations for improving this publication by the

individual user is encouraged.

Reports should be

1-4. Special Information

submitted on DA Form 2028 (Recommended Changes

Usable on codes are included in column 3.

to Publications) and forwarded direct to Commander, US

Uncoded items are applicable to all models.

Army Electronics Command, ATTN: AMSEL-MA-CRA,

Identification of the usable on codes used in this

Fort Monmouth, NJ., 07703.

publication are--

(Next printed page is 6)