Special Information - TM-11-5805-727-34P-50004

TM 11-5805-727-34P

EE119-EA-PLG-050/E110 OA9102 ,3,4,5

TO 31W1-2FSC-5

Recoverability

Definition

4. Special Information

Codes

a. The following publication pertains to the

D Reparable item. When beyond lower level repair

TA1021/FSC and its components: TM 11-5805-727-34-

capability, return to depot. Condemnation and

5, Orderwire-Operator Access Unit TA-1021/FSC.

disposal not authorized below depot level.

b. National stock numbers (NSN's) that are

Reparable item.

Repair, condemnation, and

missing from P source codes items have been applied

disposal not authorized below depot/ specialized

for and will be added to this TM by future change/revision

repair activity level.

when they are entered in the Army Master Data File

A Item requires special handling or condemnation

(AMDF). Until the NSN's are established and published,

procedures because of specific reasons (i.e., precious

submit exception requisitions to: Commander, US Army

metal content, high dollar value, critical material or

Communications-Electronics Command and

Fort

hazardous

material).

Refer

appropriate

Monmouth, ATTN: DRSEL-MM, Fort Monmouth, New

manuals/directives for specific instructions.

Jersey 07703 for the part required to support your

c. National Stock Number. Indicates the National

equipment.

stock number assigned to the item and will be used for

5. How to Locate Repair Parts

requisitioning purposes.

a. When National stock number or part number is

d. Federal Supply Code for Manufacturer

unknown.

(FSCM). The FSCM is a 5-digit numeric code listed in

(1) First.

Using the table of contents,

SB 708-41/42 which is used to identify the manufacturer,

determine the functional group within which the item

distributor, or Government agency, etc.

belongs.

This is necessary since illustrations are

e. Part Number. Indicates the primary number

prepared for functional groups and listings are divided

used by the manufacturer (individual, company, firm,

into the same groups.

corporation, or Government activity), which controls the

(2) Second. Find the illustration covering the

design and characteristics of the item by means of its

functional group to which the item belongs.

engineering drawings, specifications, standards, and

(3) Third. Identify the item on the illustration

inspection requirements to identify an item or range of

and note the illustration figure and item number of the

items.

item.

NOTE

(4) Fourth. Using the Repair Parts Listing,

When a stock numbered item is

find the figure and item number noted on the illustration.

b. When National stock number or par number is

requisitioned, the repair par received

known.

may have a different part number

(1) First Using the Index of National Stock

than the part being replaced.

Numbers and Part Numbers, find the pertinent National

Description. Indicates the Federal item name

stock number or part number. This index is in NIIN

and, if required, a minimum description to identify the

sequence followed by a list of part numbers in

item.

alphanumeric sequence, cross-referenced to the

g. Unit of Measure (U/M). Indicates the standard

illustration figure number and item number.

of the basic quantity of the listed item as used in

(2) Second. After finding the figure and item

performing the actual maintenance function.

This

number, locate the figure and item number in the repair

measure is expressed by a two-character alphabetical

parts list.

abbreviation (e.g., ea, in, pr, etc). When the unit of

6. Abbreviations

measure differs from the unit of issue, the lowest unit of

Not applicable.

issue that will satisfy the required units of measure will

(next printed page is 4)

be requisitioned.

h. Quantity Incorporated in Unit. Indicates the

quantity of the item used in the breakout shown on the

illustration figure, which is prepared for a functional

group, subfunctional group, or an assembly.