Click here to make tpub.com your Home Page

Page Title: CM MSA PC CARD COMPONENT PERFORMANCE TEST
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

T.O. 31S5-4-308-1
TM 11-5805-663-14-13
NAVELEX 0967-464-0010
a. Open Program Maintenance Panel
a. Open Program Maintenance Panel.
b. On Processor Auto-Load PC card
b. On Processor Auto-Load PC card
A1A3A9, set the four red toggle switched
A1A3A9, set the four red toggle switches,
designated from top to bottom as S1 three
designated from top to bottom as S1 through
S4, as follows: S1 and S2 to up position
S4, as follows: S1 and S2 to up position,
S3 and S4 to down position.
S3 and S4 to down position.
Mount and thread ATP tape on Mag
Mount and thread ATP tape on Mag
Tape Unit 1 (A1A1).
Tape Unit 1 (A1A1).
d. On Mag Tape Unit, perform the
d. On Mag Tape Unit, perform the
following:
following:
1. Press LOAD switch.
1. Press LOAD switch.
2. When tape movement stops pre-
2. When tape movement stops press
LOAD switch again.
LOAD switch again.
3. When LOAD lamp is lighted,
3 .  When LOAD lamp is lighted, press
ON LINE switch.
ON LINE switch.
4. If LOAD lamp is not lighted after
4. If LOAD lamp is not lighted after
the tape reel has made five or more reva-
the tape reel has made five or more revolu-
tions, press REWIND switch; then, when
tions, press REWIND switch; then, when
LOAD lamp lights, press ON LINE switch
LOAD lamp lights, press ON LINE switch.
e . Press reset and load switches.
Press reset and load switches.
e.
f. When tape motion stops, repeat
f. When tape motion stops, repeat step
four more times to reach the fifth program
e four more times to reach the fifth program
(GIN 4). Tape motion must stop after each
(GIN 4). Tape motion must stop after each
load.
load.
g . Press run switch after the fifth lo
Press run switch after the fifth load.
g.
NOTE
NOTE
A loop count will appear in bits 4 to
A loop count will appear in bits 4 to
15 and bit 2 will light to indicate
15 and bit 2 will light to indicate
GIN 4 is operating.
GIN 4 is operating.
h. Go to step 7 of table 6-26.
h. Go to step 8 of table 6-27.
6-52. CM MSA PC CARD COMPONENT
6-54. CM MBA PC CARD COMPONENT
PERFORMANCE TEST. The component per-
PERFORMANCE TEST. The component per
formance test for the CM MSA PC card is
formance test for the CM MBA PC card is
used to isolate malfunctions to an IC or
used to isolate malfunctions to an IC or
group of IC's.  To accomplish the CM MSA
group of IC's. To accomplish the CM M
PC card component performance test perform
PC card component performance test perform
the procedure in table 6-27.
the procedure in table 6-28.
6-53. After step 6 of table 6-27, load AT?
6-55. After step 6 of table 6-28, load the
tape as follows:
ATP tape as follows:

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business