 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 Voltage Requirements:
PH-129; PH-129-B or EN-16(1) ...........................
105- to 120-volt dc or 60-cycle ac.
PH-129-A and PH-639(*) /TF ...............................
105- to 120-volt ac or 6- to 8volt dc.
Condenser lens sets .........................................................
3 1/2-inch diameter set.
..............................................................
61-inch diameter set.
Projection lens sets:
PH-639A/TF or EN-16(1)......................................
2-inch focal length.
..............................................................
5 3/8-inch focal length.
PH-129-(*) or PH-3-639/TF ..................................
2-inch focal length.
..............................................................
5 1/2-inch focal length.
Projection lens openings:
PH-129-(*) or PH-639(*) /TF.................................
F/4.5 through f/32.
EN-16(1) F/4.5 through f/22.
Holders PH349 and PH-349-A ..........................................
Holds enlarging paper up to 11 by 14 inches in size, with
..............................................................
adjustments for margins up to 3 inches in width.
Boards PH-317 and PH-317-A ..........................................
Holds enlarging paper up to 8 by 10 inches in size, with
..............................................................
adjustments for margins up to % inch in width.
Projection Printing Easel FN-10(1) ....................................
Holds enlarging paper up to 11 by 14 inches in size, with
..............................................................
adjustments for margins up to % inch in width.
Dustless negative carrier:
PH-129-(*) or PH-639(*) /TF.................................
3 5/8- by 4 5/8-inch aperture.
EN-16(1) 4- by 5-inch aperture.............................
4- by 5-inch aperture
Glass negative carrier .......................................................
4- by 5-inch aperture.
Rapid-shift negative carrier ...............................................
1- by 1 1/2-inch aperture (for 35-mm film).
b. Minor Components.
Timer PH-29-C and Stop Timer FM-103(1):
Power Source .......................................................
Spring motor.
Time range ...........................................................
1 second to 60 minutes.
Timer PH-42-C:
Voltage requirement- ............................................
105- to 120-volt ac.
Time range ...........................................................
1 second to 55 seconds.
Timer PH-426, PH-426-A or Interval Timer FN-5 (1):
Voltage requirements _ ........................................
105- to 120-volt ac.
Time range ...........................................................
1second to 60 seconds.
Foot Switch PH-424:
Type
..............................................................
Foot pressure actuated
Voltage requirement ............................................
6- to 8-volt dc or 105- to 120-volt dc.
Lamp PH-422A:
Voltage requirement .............................................
10- to 120-volt ac or dc or 6- to 8volt dc.
Type
..............................................................
Safelight.
Filters
..............................................................
Three light filters; green-yellow, red, and dark-green.
Tank PH-186 or Photographic Processing Tank
FM-12(1):
Type
..............................................................
Daylight-developing tank.
Film type ..............................................................
35-mm roll-film.
Film capacity.........................................................
66 inches.
Tank PH-256-A or Photographic Processing Tank
FM-8(1):
Type
..............................................................
Daylight-developing tank.
Film type ..............................................................
Cut-film up to 4 by 5 inches.
Film capacity.........................................................
12 negatives.
Thermometer PH-660/U ....................................................
Bimetallic, self-indicating; 0' to +140' F.
components of Printer PH-129-(8), Printer PH-639
5. Components
(*)/TF, and Photographic Projection Printer EN-16(1) are
The components of Processing Equipment PH-406 and
listed in b below. The asterisk indicates the equipment
Photographic Film Processing Unit ES-20(1) are listed in
with which the particular component is supplied.
a
below.
The
major
AGO 5894A
4
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals